Delta - HPE Compute Solutions - HPE0-S60 Exam Practice Test

Question 1

Your customer has an HPE Synergy frame equipped with a D3940 Storage Module. Each of the compute nodes has an appropriate storage controller Installed and two 12Gb SAS switches installed in the first fabric.
The customer reports that compute nodes cannot access the storage module. What should you verify first when troubleshooting this problem?

A. If there is at least one ISCSI network configured that will provide access to the module.

B. If the D3940 storage module is property licensed through HPE OneView interface.

C. If there Is a logical interconnect created based on the 12Gb SAS switches.

D. If the D3940 module is imported in managed state that allows volume provisioning.

Correct Answer: C

Explanation: Only visible for Actualtests4sure members. You can sign-up / login (it's free).

Question 2

Which HPE Virtual Connect feature allows an administrator to suppress excessive inbound multicast broadcast and destination lookup failure (OLF) packets?

A. LLDP tagging

B. Pause flood protection

C. Storm control

D. Loop protection

Correct Answer: C

Explanation: Only visible for Actualtests4sure members. You can sign-up / login (it's free).

Question 3

Your customer plans to add four HPE Synergy frames to an existing management ring Ail installed frames are equipped with two 2-port FLM modules, while new frames will be equipped with 4-port FLM modules.
Which statement about mixing different FLM modules is true?

A. Mixing different FLM modules is allowed if all of them have the same firmware version

B. A management ring can contain mixed frame link module configurations

C. Existing 2-port FLM modules must be replaced with 4-port FLM modules

D. A management ring with mixed FLM modules cannot have more than 12 frames

Correct Answer: B

Explanation: Only visible for Actualtests4sure members. You can sign-up / login (it's free).

Question 4

Match each HPE OneView network type with its definition.

Correct Answer:

Explanation:
Here are the correct matches for each HPE OneView network type with their respective definitions:
* Internal networkDefinition:A network that does not utilize any uplink ports and is used for communication between servers in the same frame.
* Tagged networkDefinition:A network in which any tagged packets are dropped and forwarding is done by a MAC address.
* Tunnel networkDefinition:A network with a dedicated set of uplink ports used to pass a group of VLANs without changing the VLAN tags.
* Untagged networkDefinition:A network that contains multiple networks on a single uplink set that allows your customer to share uplinks with those networks.
* Internal network:This network type facilitates communication between servers within the same frame without utilizing uplink ports, providing internal data exchange.
* Tagged network:This network type drops any packets that are tagged and forwards packets based on their MAC address, ensuring only untagged traffic is processed.
* Tunnel network:This type of network uses a specific set of uplink ports to pass VLAN groups while preserving the VLAN tags, useful for maintaining VLAN configurations across different network segments.
* Untagged network:This network type enables the sharing of uplinks among multiple networks by placing them on a single uplink set, useful for optimizing network resource usage.

Question 5

Which statement about HPE Apollo 2000 Gen10 Plus platform is true?

A. It offers servers with AMD EPYC and Intel Xeon Scalable CPUs

B. It is fully managed using HPE OneView including all connections

C. It is equipped with HPE Persistent memory by default

D. It can support a single processor only and up to 4 per chassis

Correct Answer: A

Explanation: Only visible for Actualtests4sure members. You can sign-up / login (it's free).

Question 6

Which statement about the HPE D3940 storage module is true?

A. it is configured through CLl available from HPE Synergy console

B. Up to five modules can be installed in a single frame with Gen10 servers

C. Only one type of drives (SATA, SAS, SSD) can be installed in each module

D. SATA drives requires redundant 10 adapters to be installed in this module

Correct Answer: B

Explanation: Only visible for Actualtests4sure members. You can sign-up / login (it's free).

Question 7

Your customer wants to compare HPE Superdome Flex with HPE Superdome Flex 280.
Which statement about these two systems is true?

A. Only HPE Superdome Flex 280 can support multiple nPars

B. Only HPE Superdome Flex supports HPE Persistent Memory

C. Only HPE Superdome Rex 280 can be managed using HPE OneView

D. Only HPE Superdome Flex supports 32 sockets and 48TB of memory

Correct Answer: D

Explanation: Only visible for Actualtests4sure members. You can sign-up / login (it's free).

Question 8

Your customer has the following HPE Synergy setup:
- 15 HPE Synergy 12000 frames with 50Gb connectivity to each server port
- 2 HPE Composer 2 modules
- 15 HPE D3940 Storage Modules, one per frame
- 2 HPE 12Gb SAS switches per frame
Which statement about this setup is true?

A. The customer must create at least five logical enclosures for this setup.

B. If properly cabled, any compute node can access any HPE D3490 storage module

C. To manage 15 frames, additional HPE Composers are required.

D. The customer can install up to 12 HPE Synergy 480 compute nodes per frame.

Correct Answer: A

Explanation: Only visible for Actualtests4sure members. You can sign-up / login (it's free).

Question 9

You configured a vVoI datastore using HPE Storage integration Pack for VMware vCenter.
Which storage object should you check using SSMC to verify whether vVol datastore is configured property?

A. App Volume Set

B. virtual Volume

C. Storage Container

D. Virtual Volume Set

Correct Answer: C

Explanation: Only visible for Actualtests4sure members. You can sign-up / login (it's free).

HP Delta - HPE Compute Solutions - HPE0-S60 Exam Practice Test

Latest Update

Useful Links

Contact Us