Huawei HCIE-Carrier IP (Written) - H31-161 Exam Practice Test
Question 1
As shown in the figure, RTA, RTB, and RTC use the OSPF protocol. The default cost value is used for links, and unicast routes converge on the entire network. The Loopback 0 interface is set to configure RTC as the RP or BSR. The SPT switching threshold uses the default value on RTB. The receiver joins the multicast group 225.1.1.1. The multicast source sends multicast data to the destination address 225.1.1.1. Which interface is the inbound interface in the (10.1.1.1, 225.1.1.1) entry on RTB?


Correct Answer: B
Question 2
Which of the following can be implemented in an IP backbone network?
Correct Answer: A,B,D
Question 3
Which statement is false?
Correct Answer: D
Question 4
In the VRP, which of the following authentication modes are supported by the secure shell (SSH)?
Correct Answer: A,B,D
Question 5
Which of the following statements about the VPLS packet forwarding are true?
Correct Answer: A,B,C
Question 6
Refer to the exhibit.

As shown in the figure, inter-AS VPN Option A is used. CE 1 and CE 2 belong to the same VPN.AS 100 and AS 200 run IGP and LDP, respectively. ASBRs communicate with each other through EBGP. The loopback interface address of CE 1 is 10.1.1.1/24. Suppose CE 2 can ping CE 1. Which router allocates an inner label when PE 2 forwards packets from CE 2 to CE
1?

As shown in the figure, inter-AS VPN Option A is used. CE 1 and CE 2 belong to the same VPN.AS 100 and AS 200 run IGP and LDP, respectively. ASBRs communicate with each other through EBGP. The loopback interface address of CE 1 is 10.1.1.1/24. Suppose CE 2 can ping CE 1. Which router allocates an inner label when PE 2 forwards packets from CE 2 to CE
1?
Correct Answer: B
Question 7
The Huawei router is the hop RD where the SSM mapping function is enabled at the interface. Some IGMPv2 hosts expect to receive (1.0.01,232.1.0.1) (1.0.0.1232.1.0.2), and (2.0.0,232.1.3.2) dat a. How can you satisfy the preceding requirement with the least configurations?
Correct Answer: A
Question 8
As shown in the figure, RTA connects to RTB and RTC. A TE tunnel is configured on RTA to reach RTC. The TE tunnel cannot be successfully established. However, CSPFbased path calculation is successful and RTA does not receive any PathErro messages. What are possible causes?
Correct Answer: B,C
Question 9
An IPTV bearer network requires the broadband TV (BTV), VOD, and near video on demand (NVOD) services. Video programs use the standard MPEG 4 codec format. Which of the following statements about the QoS policy are true?
Correct Answer: B,C
Question 10
As shown in the figure, IGP is configured on RT 1 and RT 2, and route 193.3.6.0/24 is configured on RT 2. Which of the following statements is correct? Suppose OSPF is used here. Configure an access control list (ACL) on RT 2 in system mode.
ACL 2000
rule 5 permit source 193.3.6.0 0.0.0.255
Configure a routing policy in system mode:
route-policy t permit node 1
if-match acl 2000
apply backup-nexthop 106.108.4.1
apply backup-interface Ethernet4/0/4
Configure the IP FRR in system mode:
ip frr route-policy tConfigure the ethe4/0/4 interface of RT 2:
ospf cost 100
Configure BFD on RT 2:
Enable BFD on Ethernet4/0/3
bfd b1 bind peer-ip 106.108.3.1 interface Ethernet4/0/3
discriminator local 1
discriminator remote 1
min-tx-interval 10
min-rx-interval 10
process-pst
commit

Configuration on RT 1:
Enable BFD on Ethernet7/0/3
bfd b1 bind peer-ip 106.108.3.2 interface Ethernet7/0/3
discriminator local 1
discriminator remote 1
min-tx-interval 10
min-rx-interval 10
process-pst
commit
ACL 2000
rule 5 permit source 193.3.6.0 0.0.0.255
Configure a routing policy in system mode:
route-policy t permit node 1
if-match acl 2000
apply backup-nexthop 106.108.4.1
apply backup-interface Ethernet4/0/4
Configure the IP FRR in system mode:
ip frr route-policy tConfigure the ethe4/0/4 interface of RT 2:
ospf cost 100
Configure BFD on RT 2:
Enable BFD on Ethernet4/0/3
bfd b1 bind peer-ip 106.108.3.1 interface Ethernet4/0/3
discriminator local 1
discriminator remote 1
min-tx-interval 10
min-rx-interval 10
process-pst
commit

Configuration on RT 1:
Enable BFD on Ethernet7/0/3
bfd b1 bind peer-ip 106.108.3.2 interface Ethernet7/0/3
discriminator local 1
discriminator remote 1
min-tx-interval 10
min-rx-interval 10
process-pst
commit
Correct Answer: C,D
Question 11
Exhibit:

As shown in the figure, RTA and have one BGP session. To detect fault fast, the BFD for BGP feature needs to be configured on RTA and RTB. BGP-related configurations are as follows:

The only Ethernet link between RTA and RTB becomes faulty when the BGP neighbor session is in ESTABLISHED state and the BFD session is in the UP state. Which statements is true? (Note: BFD works in asynchronous mode)

As shown in the figure, RTA and have one BGP session. To detect fault fast, the BFD for BGP feature needs to be configured on RTA and RTB. BGP-related configurations are as follows:

The only Ethernet link between RTA and RTB becomes faulty when the BGP neighbor session is in ESTABLISHED state and the BFD session is in the UP state. Which statements is true? (Note: BFD works in asynchronous mode)
Correct Answer: B
Question 12
Which of the following are conditions for bringing the remote CCC connection Up? (ABE)
Correct Answer: A,D,E
Question 13
Which of the following statements about LDP-IGP synchronization are true?
Correct Answer: A,B,D

