NetApp Certified Support Engineer ONTAP Specialist

Question 1

You have a customer who is concerned with high CPU and disk utilization on their SnapMirror destination system. They are worried about high CPU and disk usage without any user operations.
In this situation, what should you tell the customer?

A. Explain that background tasks such as SnapMirror throttle up in the absence of user workload.

B. Explain that only user workload should use the CPU and Investigate further.

C. Suggest that the customer manually cancel any scanners on the destination to reduce CPU usage.

D. Suggest that the customer throttle their SnapMirror relationships to reduce resource consumption.

Correct Answer: A

Explanation: Only visible for Actualtests4sure members. You can sign-up / login (it's free).

Question 2

A customer reports that some of their client computers are unable to access a FlexGroup over CIFS. This problem involves only their older Windows XP clients and some printers and scanners.
In this scenario, which statement Is correct?

A. FlexGroup requires CIFS shares to use the Continuously Available Feature, which these clients do not support.

B. FlexGroup requires CIFS shares to be located in qtrees, which these clients do not support.

C. These systems use the SMQI protocol which Is an unsupported feature in FlexGroup

D. These systems use Offloaded Data Transfer, which is an unsupported feature in FlexGroup.

Correct Answer: A

Explanation: Only visible for Actualtests4sure members. You can sign-up / login (it's free).

Question 3

The motherboard of Node-01 is being replaced. To perform this task, a takeover was Initiated from Node-02. Node-02 panics showing the string below.
PANIC; Permanent errors on all HA mailbox disks (while marshalling header) in SKprocess fnmbx_instanceWorker on release 9.5P8 (C) What has happened in this situation?

A. While in maintenance mode, the mailbox destroy local command was executed.

B. While in maintenance mode, the sldiag device show command was executed.

C. While in maintenance mode, the HA_config show command was executed.

D. While in maintenance mode, the fcadmin device_map command was executed.

Correct Answer: A

Explanation: Only visible for Actualtests4sure members. You can sign-up / login (it's free).

Question 4

Your customer has mounted an NFS SVM from a Linux client unci performance is very poor. The customer is certain that they have jumbo frames enabled. They have verified an MTU of 9000 on both the Linux client and the broadcast domain on the NetApp ONTAP 9.8 cluster.

Referring to the exhibit, which ONTAP command will help isolate a possible MTU mismatch?

A.

B.

C.

D.

Correct Answer: B

Explanation: Only visible for Actualtests4sure members. You can sign-up / login (it's free).

Question 5

You Just used the CLI to create a NetApp ONTAP FlexGroup Volume on a NetApp Cloud Volumes ONTAP instance. After creation, you notice odd behavior in NetApp Cloud Manager.
In this scenario, what Is the reason for this behavior?

A. Cloud Manager must be used to provision the FlexGroup volume.

B. The Capacity Management Mode within Cloud Manager should be set to Automatic.

C. The Capacity Management Mode within Cloud Manager should be set to Manual.

D. Cloud Volumes ONTAP does not support FlexGroup volumes.

Correct Answer: C

Explanation: Only visible for Actualtests4sure members. You can sign-up / login (it's free).

Question 6

You are attempting to connect a NetApp ONTAP cluster to a very complex network that requires LIFs to fail over across subnets.
How would you accomplish this task?

A. Configure VIP LIFs using BGP.

B. Configure VIP LIFs using OSPF.

C. Configure a I IF failover policy for each subnet inside a single broadcast domain.

D. Configure an equal number of UFs on each subnet.

Correct Answer: A

Explanation: Only visible for Actualtests4sure members. You can sign-up / login (it's free).

Question 7

A customer reports that while Installing Windows updates on their external Vscan servers, clients could not access any files on their CIF-S SVM. The problem disappeared after the update process was completed. The customer wants to prevent this issue from happening during the next patch window.
In this scenario, what are two ways to accomplish this task? (Choose two.)

A. Disable the -scan-mandatory flag in the Vscan policy.

B. Update the Vscan servers one at a time.

C. Modify the CIFS shares to be continuously available (CA) shares.

D. Enable the -scan-mandatory flag in the Vscan policy.

Correct Answer: A,B

Explanation: Only visible for Actualtests4sure members. You can sign-up / login (it's free).

Network Appliance NetApp Certified Support Engineer ONTAP Specialist - NS0-593 Exam Practice Test

Latest Update

Useful Links

Contact Us