Fortinet NSE 5 - FortiSwitch 7.6 Administrator - NSE5_FSW

Question 1

(Full question statement start from here)
How does FortiSwitch determine the route for traffic traversing its interfaces? (Choose one answer)

A. FortiSwitch forwards all traffic to FortiGate for routing decisions.

B. ASIC hardware routing can handle only dynamic routing, if supported.

C. Hardware-based routing on FortiSwitch is handled by the CPU.

D. FortiSwitch looks up the hardware routing table and then the forwarding information base (FIB).

Correct Answer: D

Explanation: Only visible for Actualtests4sure members. You can sign-up / login (it's free).

Question 2

(Full question statement start from here)
You enable Dynamic Host Configuration Protocol (DHCP) snooping on a VLAN and configure a FortiSwitch port astrustedfor DHCP snooping. What additional step is required to configure the port as trusted for Dynamic ARP Inspection (DAI)? (Choose one answer)

A. DAI implicitly trusts the port.

B. Enable static MAC learning on the port.

C. Enable IP Source Guard (IPSG) on the port.

D. Manually set the port as trusted for DAI through the CLI.

Correct Answer: A

Explanation: Only visible for Actualtests4sure members. You can sign-up / login (it's free).

Question 3

An administrator must deploy managed FortiSwitch devices in a remote location where multiple VLANs must be used to segment devices. No layer 3 switch or router is present at the site, and the only WAN connectivity is an ISP-provided router connected to the public internet. Which two components are required to enable VLAN segmentation across this remote site? (Choose two answers)

A. FortiGate with a layer 3 interface to terminate the VXLAN overlay

B. A layer 3 router at the remote location to handle inter-VLAN routing

C. FortiGate and FortiSwitch configured with VXLAN to tunnel VLANs over the WAN

D. FortiSwitch and FortiGate devices configured with IPsec interfaces

E. A FortiSwitch model that supports VXLAN hardware acceleration

Correct Answer: A,C

Explanation: Only visible for Actualtests4sure members. You can sign-up / login (it's free).

Question 4

How is traffic routed on FortiSwitch?

A. Layer 3 routing can be configured on FortiSwitch, while managed by FortiGate.

B. ASIC hardware routing can only handle dynamic routing, if supported.

C. Hardware-based routing on FortiSwitch is handled by the CPU.

D. FortiSwitch looks up the hardware routing table and then the forwarding information base (FIB).

Correct Answer: A

Explanation: Only visible for Actualtests4sure members. You can sign-up / login (it's free).

Question 5

(Full question statement start from here)
Refer to the exhibit.

You run the command diagnose switch-controller switch-info loopguard access-1 and see that theMAC-Move column displays a value of0forport1.
What does this indicate? (Choose one answer)

A. Port1 will shut down if a loop occurs on any VLAN.

B. Port1 is not being monitored by loop guard.

C. The MAC move feature is not enabled.

D. Loop guard is disabled on port1.

Correct Answer: C

Explanation: Only visible for Actualtests4sure members. You can sign-up / login (it's free).

Question 6

What happens when a routed VLAN interface (RVI) is configured on a FortiSwitch port or trunk? (Choose one answer)

A. All VLANs on the port are terminated in a trunk by default.

B. VLAN 1 is automatically assigned for management.

C. The port becomes a layer 3 interface with VLAN 4095 assigned automatically.1

D. The port becomes a layer 3 interface and assigned to VLAN 1.

Correct Answer: C

Explanation: Only visible for Actualtests4sure members. You can sign-up / login (it's free).

Question 7

You are deploying a small office network with a single FortiGate and a single FortiSwitch. The office currently has moderate traffic, but the IT team expects the network to grow in the near future, adding more FortiSwitch devices and endpoints. Which FortiLink configuration should you deploy to provide the best combination of current performance and scalability for future growth? (Choose one answer)

A. Configure FortiLink using software-based switch interfaces.

B. Configure FortiLink as a link aggregation group (LAG) interface.

C. Configure FortiLink using hardware-based switch interfaces.1

D. Configure FortiLink as a multichassis LAG (MCLAG) interface.2

Correct Answer: B

Explanation: Only visible for Actualtests4sure members. You can sign-up / login (it's free).

Question 8

Refer to the exhibit.

Core-1 and Access-1 are managed and authorized by FortiGate-1. which uses port4 as the FortiLink interface.
After FortiGate authorizes and manages Core-2. Port1 status becomes STP discarding.
Why is port1 in the discarding state?

A. Access-1 is the root bridge and can only have one root port.

B. Core-2 has the lowest bridge priority.

C. Core-1 and Core-2 do not have MCLAG configuration.

D. port1 on Core-2 is discarding only management traffic.

Correct Answer: C

Explanation: Only visible for Actualtests4sure members. You can sign-up / login (it's free).

Fortinet NSE 5 - FortiSwitch 7.6 Administrator - NSE5_FSW_AD-7.6 Exam Practice Test

Latest Update

Useful Links

Contact Us