[2022] NACE-CIP2-001 Actual Exam Dumps, NACE-CIP2-001 Practice Test
Actualtests4sure NACE-CIP2-001 dumps & CIP Level 2 sure practice dumps
NEW QUESTION 60
Eddy current DFT gauges are used to measure Dry Film Thickness in which of the following situations:
- A. Conductive coatings applied to a magnetic metallic substrate
- B. Magnetic coatings applied to a magnetic metallic substrate
- C. Conductive coatings applied to a cementitious substrate
- D. Non-Conductive coatings applied to a conductive metallic substrate
Answer: D
NEW QUESTION 61
When a coating is expected to be exposed to temperatures above 93C (200 F) the best choice would be:
- A. Organic coatings
- B. Inorganic Coatings
- C. Polyurea
- D. Latex
Answer: B
NEW QUESTION 62
Non-Conformance Reports are designed to:
- A. Punish the Contractor for substandard work
- B. Elevate the status of the Inspector
- C. Assist the Owner in negotiating credits from the Contractor
- D. To identify items that do not meet the specification requirements
Answer: D
NEW QUESTION 63
Coating Surveys are legally required:
- A. On commercial marine vessels and offshore platforms
- B. On food and beverage vessels and can linings
- C. On high pressure gas lines and fireproofed structures
- D. On water tanks and potable water pipelines
Answer: A
NEW QUESTION 64
The coating applicator has ignored a enface preparation hold point and applied coating over the surface without a sign off from you as the inspector.
Your FIRST preferred course of action is to:
- A. Advise the Owner and write a Non-Conformance report
- B. Ignore the situation
- C. Stop the job
- D. Require the Applicator to remove the coating
Answer: D
NEW QUESTION 65
A reinforced coating is
- A. more resistant to movement, abrasion, and impact than a non-reinforced coating.
- B. equally resistant to movement and impact as a non-reinforced coating.
- C. less resistant to movement, abrasion, and impact than a non-reinforced coating.
- D. equally resistant to abrasion and impact as a non-reinforced coating.
Answer: A
NEW QUESTION 66
The number of air turns in an enclosure can be affected by all of these EXCEPT
- A. coating type.
- B. type of dehumidification equipment (refrigerant or desiccant).
- C. manufacturer of the equipment.
- D. time of the year (winter/summer).
Answer: A
NEW QUESTION 67
Inspection and Test plans are developed by referencing:
- A. The Specification, Safety Manual, Relevant Standards and Codes
- B. The Specification, Application Guidelines, 'Relevant Standards and Codes
- C. The Specification, SDS, relevant Standards and Codes
- D. The Specification, TDS, relevant Standards and Codes
Answer: D
NEW QUESTION 68
You have just your NACE CIP Level 2 certification when you are asked to supervise a team of uncertified field pipeline inspectors.
Your FIRST preferred course of action is to:
- A. Accept assignment without hesitation
- B. Advise the prospective employer that you cannot accept the position
- C. Meet with the prospective employer to scope of your role
- D. Review the NACE Attestation prior to making a decision
Answer: D
NEW QUESTION 69
From a corrosion perspective, the main difference between Ferrous and Non-Ferrous Metals is:
- A. Iron content
- B. Safety
- C. Appearance
- D. Cost
Answer: A
NEW QUESTION 70
You are a NACE Level 2 Coating Inspector who has just arrived on a job in progress where there is no Inspection and Test Plan (ITP). The first morning you arrive the job is behind schedule and you are asked to take DIY Film Thickness readings.
Your FIRST preferred course of action is to:
- A. Call your supervisor
- B. Use a generally accepted industry standard and to take readings
- C. Refuse to take readings until an is in place
- D. Develop your own methodology and proceed take the readings
Answer: B
NEW QUESTION 71
Cold-applied tape
- A. is typically green or led and looks like "painted" finish.
- B. is polyethylene film, heat laminated, 'With an adhesive layer of butyl glue.
- C. have a cross-linked polyethylene backing and a heat-activated adhesive.
- D. are identifiable by its distinct colors, usually light blue, green, Or Grey.
Answer: B
NEW QUESTION 72
You are NACE Level 2 Inspector working on a tank lining job where a mobile centrifugal blast unit is being used to blast the tank floor to a NACE No.1/SSPC SP 5. The Contractor has completed his final blast and has called for a hold point inspection. This is the 1 st time you have seen field based centrifugal blast cleaning. You observe what appears to be staining on the substrate however the Contractor assures you this is normal when using centrifugal blast units and what you are seeing is what is defined in the standard as an acceptable variation in appearance.
Your FIRST preferred course of action is to:
- A. Call your supervisor
- B. Review the standard with the Contractor and re-inspect the floor
- C. Shut the job down
- D. Request that the Contractor re-blast the floor
Answer: B
NEW QUESTION 73
You are the new NACE Level 2 Inspector on a job which had been very problematic. The previous Inspector was fired duo to personality conflicts with the Contractor's supervisor. Upon arriving onsite the Contractor's supervisor advises you in no uncertain terms that you will be the next to go, unless you cooperate with him.
Your FIRST preferred course of action is to:
- A. Express a willingness to work with the site team and follow the specification
- B. Suggest to the Owner that the supervisor should be removed from site
- C. Defend the previous inspector
- D. Challenge the supervisor's authority
Answer: A
NEW QUESTION 74
You are the NACE Inspector on a project where a stationary floating structure is being coated and you notice a self-smoothing anti-fouling coating has been specified.
This is not a good choice because:
- A. It contains biocide
- B. The floating structure is stationary
- C. It doesn't contain biocide
- D. It will result in a very slippery surface
Answer: A
NEW QUESTION 75
The Concrete Repair Institute's comparators can be used to assess:
- A. Surface cleanliness prior to coating
- B. Surface profile prior to coating
- C. Contamination levels prior to coating
- D. Compressive and tensile strength prior to coating
Answer: B
NEW QUESTION 76
NACE No.13/ SSPC 6 identifies the use of:
- A. Abrasive blasting only
- B. Watterjetting only
- C. Various methods of cleaning
- D. Steam cleaning only
Answer: C
NEW QUESTION 77
Ideally, documentation requirements should be defined:
- A. By the inspector
- B. By the contractor
- C. In the specification
- D. At the pre-job conference
Answer: C
NEW QUESTION 78
When observing design defects the NACE Inspector should:
- A. Request that the item be rebuilt with a better design for coating
- B. Ignore the defect as the inspector can't change the design
- C. Stop the job immediately
- D. Document the defect and the potential problems that could result
Answer: D
NEW QUESTION 79
Linings are used on the interior of pipelines to
- A. reduce magnetic polarity.
- B. afford limited temperature insulation.
- C. protect the transported product.
- D. provide protection against soil chemicals.
Answer: C
NEW QUESTION 80
You are working as the only in-house NACE Level 2 Inspector in a shop setting when an independent 3 rd party NACE Level 3 Inspector, representing the owner, presents you with a copy of a Non Conformance Report (NCR) he has written for a NACE2/SSPC SP 10 centrifugal blast which you had previously approved.
Your FIRST preferred course of action is to:
- A. Consult your supervisor
- B. Request a re-blast of the item in question
- C. Review the NCR with the other Inspector
- D. Verbally challenge the NCR
Answer: A
NEW QUESTION 81
......
NACE-CIP2-001 Actual Questions and Braindumps: https://www.actualtests4sure.com/NACE-CIP2-001-test-questions.html
Pass NACE-CIP2-001 Exam with Updated NACE-CIP2-001 Exam Dumps PDF 2022: https://drive.google.com/open?id=1c47P6pXzTqHyluJ2ll1grDiVaOMFD9Y9
