Updated Aug-2024 Test Engine to Practice ECP-206 Test Questions
ECP-206 Real Exam Questions Test Engine Dumps Training With 62 Questions
NEW QUESTION # 33
Which two statements are true about the Ericsson Router 6000 series? (Choose two.)
- A. The Router 6000 uses the same building practice and accessories as the Ericsson Radio System.
- B. The Router 6000 is solely built as a radio cell site router.
- C. The Router 6000 products range from all-outdoor small site routers to large aggregation routers.
- D. The Router 6000 can host containerized applications such as firewalls.
Answer: A,C
Explanation:
Explanation
Two statements that are true about the Ericsson Router 6000 series are:
The Router 6000 uses the same building practice and accessories as the Ericsson Radio System. The Ericsson Radio System is a modular and scalableradio access network solution that supports multiple standards, bands, and layers. The Router 6000 series is fully integrated into the Ericsson Radio System, using the same building practice and accessories such as mounting kits, cables, power supplies, etc. This simplifies installation, operation, and maintenance of both radio and transport equipment78.
The Router 6000 products range from all-outdoor small site routers to large aggregation routers. The Router 6000 series consists of three main products: the Router 6672 for access, the Router 6675 for pre-aggregation, and the Router 6274 for metro aggregation. The Router 6672 is an all-outdoor small cell site router with high-capacity and low-power consumption. The Router 6675 is a combined access and E-RAN switch with hardware-accelerated IPSec and high-accuracy internal clock. The Router 6274 is a high-capacity metro aggregation router with SDN functionality and flexible interface options78.
References: Router 6000 Series - Ericsson, New Ericsson Router 6000 series couples radio and IP transport for 5G future - Global Brands Magazine
NEW QUESTION # 34
What is the CLI command to obtain the software version in Ericsson Router 6000 products?
- A. show log
- B. show sysstat
- C. show release
- D. show version
Answer: D
Explanation:
Explanation
The CLI command to obtain the software version in Ericsson Router 6000 products is show version. This command displays information about the software release, the hardware model, the serial number, the uptime, and the boot image of the router. References: [ERICSSON SMARTEDGE 600 HARDWARE MANUAL Pdf Download | ManualsLib], Ericsson Router 6000 Series - Ericsson
NEW QUESTION # 35
What is a reason for using VLANs in an IP network?
- A. to enable MAC address learning on a router port
- B. to isolate hosts across multiple IP subnets
- C. to isolate hosts within the same IP subnet
- D. to implement virtual routing
Answer: C
Explanation:
Explanation
A reason for using VLANs in an IP network is to isolate hosts within the same IP subnet. VLANs (Virtual LANs) are logical grouping of devices in the same broadcast domain. VLANs are usually configured on switches by placing some interfaces into one broadcast domain and some interfaces into another. Each VLAN acts as a subgroup of the switch ports in an Ethernet LAN. VLANs allow network administrators to group hosts together even if the hosts are not directly connected to the same network switch. By using VLANs, hosts within the same IP subnet can be separated into different broadcast domains, which enhances security, reduces network congestion, and simplifies network management78.
References: 8 Different Types of VLANs in TCP/IP Networks, What is a VLAN? - Study-CCNA
NEW QUESTION # 36
Which protocol would be used to bundle multiple Ethernet ports into a virtual link with an aggregated bandwidth?
- A. ERP
- B. RSTP
- C. LACP
- D. VRRP
Answer: C
Explanation:
Explanation
The protocol that would be used to bundle multiple Ethernet ports into a virtual link with an aggregated bandwidth is LACP, which stands for Link Aggregation Control Protocol. LACP is a protocol that allows two or more devices to negotiate the formation of a link aggregation group (LAG), also known as an EtherChannel or a port channel. A LAG combines multiple physical links into one logical link that provides increased bandwidth, load balancing, and redundancy. LACP is defined in IEEE 802.3ad and 802.1AX standards12.
References: Link Aggregation Control Protocol - Wikipedia, What is "link aggregation" and how does it benefit your network? | PC Gamer
NEW QUESTION # 37
What is the purpose of penultimate hop popping?
- A. to reduce the load on the LER
- B. to reduce the load on the LDP
- C. to reduce the load on the LSP
- D. to reduce the load on the LSR
Answer: A
Explanation:
Explanation
Penultimate hop popping (PHP) is a function performed by certain routers in an MPLS enabled network. It refers to the process whereby the outermost label of an MPLS tagged packet is removed by a label switch router (LSR) before the packet is passed to an adjacent label edge router (LER). The purpose of PHP is to reduce the load on the LER, as it saves one cycle of label lookup. The LER can forward the packet based on its IP header or another label in the stack, without having to process the outer label. PHPfunctionality is achieved by the LER advertising a label with a value of 3 to its neighbors. This label is defined as "implicit-null" and informs the neighboring LSRs to perform PHP12.
References: Penultimate hop popping - Wikipedia, MPLS Penultimate hop popping - NetworkLessons.com
NEW QUESTION # 38
In OSPFv2, which route characteristic is used to determine the best path?
- A. packet loss
- B. jitter
- C. delay
- D. cost
Answer: D
Explanation:
Explanation
In OSPFv2, the route characteristic that is used to determine the best path is the cost. The cost is a metric that represents the link bandwidth, delay, reliability, or other factors. The cost is inversely proportional to the bandwidth, meaning that a higher bandwidth link has a lower cost. The cost of a route is calculated by adding the costs of all links along the path. OSPFv2 uses the following formula to calculate the cost of an interface:
Cost = Reference bandwidth / Interface bandwidth in bps
The reference bandwidth is a constant value that can be configured by the network administrator. By default, it is 100 Mbps. The interface bandwidth is the actual bandwidth of the interface in bits per second. For example, if an interface has a bandwidth of 10 Mbps, its cost would be 100 Mbps / 10 Mbps = 101415.
OSPFv2 does not use jitter, packet loss, or delay as route characteristics to determine the best path. Jitter is the variation in latency or delay between packets. Packet loss is the percentage of packets that are dropped or corrupted during transmission. Delay is the time it takes for a packet to travel from source to destination. These characteristics are not part of the OSPFv2 protocol and are not advertised in OSPFv2 LSAs1617.
References: OSPF Metric cost Calculation Formula Explained - ComputerNetworkingNotes, OSPF Cost - OSPF Routing Protocol Metric Explained - Study-CCNA, Open Shortest Path First - Wikipedia, OSPF Metric
= Cost - Cisco
NEW QUESTION # 39
Within an IGP area, which two statements are correct? (Choose two.)
- A. Routers advertise information about themselves.
- B. Routers discard valid but inaccurate information from neighbors.
- C. Routers relay information delivered by neighbors.
- D. Routers summarize information they learn from neighbors.
Answer: A,C
Explanation:
Explanation
Within an IGP area, routers advertise information about themselves and relay information delivered by neighbors. This is how link-state routing protocols such as OSPF and IS-IS work. They flood information about the network topology to all routers in the same area or domain. That information is then used to build a complete network connectivity map and to calculate the shortest path to destinations. Routers do not summarize or discard information within an area, unless they are configured to do so by some filtering mechanism. References: Ericsson IP Networking - Routing Protocols, IP Routing: ISIS Configuration Guide - IS-IS Overview and Basic Configuration
NEW QUESTION # 40
Which two statements are true regarding the LSP? (Choose two.)
- A. The LSP refers to a sequence of routers that forward the MPLS packet based on labels.
- B. The LSP refers to a sequence of routers that add. remove, or change label values along the path.
- C. The LSP refers to a sequence of routers that add, remove, or change label values based on the destination MAC address.
- D. The LSP refers to a specific label assigned to a packet by the LSR for a destination.
Answer: A,B
Explanation:
Explanation
Two statements that are true regarding the LSP are:
The LSP refers to a sequence of routers that forward the MPLS packet based on labels. An LSP is a Label Switched Path, which is a path through an MPLS network that is established by signaling protocols such as LDP or RSVP-TE. An LSP consists of a sequence of routers (called Label Switching Routers or LSRs) that forward packets based on labels rather than IP addresses. Labels are short fixed-length identifiers that are attached to packets at the ingress router and removed at the egress router. Labels can be swapped or popped at intermediate routers according to their label forwarding tables78.
The LSP refers to a sequence of routers that add, remove, or change label values along the path. As mentioned above, an LSP consists of a sequence of routers that forward packets based on labels. Along the path, different routers may perform different operations on the labels depending on their role and configuration. The ingress router adds one or more labels to the packet before sending it into the MPLS network. The egress router removes all labels from the packet before sending it out of the MPLS network. The intermediate routers may swap one label with another label according to their label forwarding tables. This process is called label switching78.
References: MPLS Fundamentals: 3 - MPLS Packet Forwarding, Multiprotocol Label Switching - Wikipedia
NEW QUESTION # 41
How do peers recognize each other's ability to use MP-BGP extensions?
- A. They advertise the ability using the capabilities field during the session establishment.
- B. They advertise the ability using the capabilities field in the End-of-RIB marker.
- C. They advertise the ability using the capabilities field in the hello packet.
- D. They advertise the ability using the capabilities field in the update packet.
Answer: A
Explanation:
Explanation
Peers recognize each other's ability to use MP-BGP extensions by advertising the ability using the capabilities field during the session establishment. MP-BGP is an extension to BGP that allows BGP to carry routing information for multiple network layer protocols, such as IPv6, VPNv4, multicast, etc. To support MP-BGP, peers need to exchange their capabilities during the session establishment phase, which consists of three steps:
open, keepalive, and update. In the open message, peers can include an optional parameter called capabilities, which indicates what kind of address families and subsequent address families they can support. If both peers agree on a common set of capabilities, they can proceed to exchange routing information for those address families using update messages56.
References: Use of MP-BGP Extensions for IPv6 Interdomain Routing, MP-EBGP Configuration Example - Cisco
NEW QUESTION # 42
Which statement about IPv6 is correct?
- A. There are four billion available addresses.
- B. Addresses are not hierarchical and are assigned at random.
- C. An interface can only be configured with one IPv6 address.
- D. Broadcast has been replaced with multicast.
Answer: D
Explanation:
Explanation
The statement about IPv6 that is correct is that broadcast has been replaced with multicast. IPv6 is the most recent version of Internet Protocol (IP), which provides an identification and location system for computers on networks and routes traffic across the Internet. IPv6 has several improvements over IPv4, such as a larger address space, simplified header format, enhanced security, and better support for mobility and QoS.One of the changes in IPv6 is that it does not support broadcast, which is a method of sending a packet to all nodes on a network segment. Instead, IPv6 uses multicast, which is a method of sending a packet to a group of nodes that have joined a multicast address34.
References: IPv6 - Wikipedia, What Is IPv6? - Cisco
NEW QUESTION # 43
Which two statements are correct for LDP? (Choose two.)
- A. LSRs send ICMP hello messages for neighbor discovery
- B. LSRs use UDP for session establishment.
- C. LSRs send UDP hello messages for neighbor discovery.
- D. LSRs use TCP to negotiate LDP session parameters.
Answer: C,D
Explanation:
Explanation
Two statements that are correct for LDP are:
LSRs send UDP hello messages for neighbor discovery. LDP is a protocol that distributes labels for MPLS forwarding along the shortest path calculated by an IGP. LDP uses two types of messages:
discovery messages and session messages. Discovery messages are used to discover and maintain adjacency with other LSRs that support LDP. Discovery messages are sent as UDP datagrams to the well-known multicast address 224.0.0.2 (all routers on this subnet) on port 64634.
LSRs use TCP to negotiate LDP session parameters. Session messages are used to establish, maintain, and terminate LDP sessions between LSRs. Session messages are also used to exchange label mappings, notification messages, and keepalive messages. Session messages are sent as TCP segments to port
64634.
References: Ldp | Microsoft Learn, Label Distribution Protocol - Wikipedia
NEW QUESTION # 44
How many different priorities are available to use in a VLAN header?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: D
Explanation:
Explanation
There are 8 different priorities available to use in a VLAN header. A VLAN header is a 4-byte field that is inserted into an Ethernet frame to indicate the VLAN membership and priority of the frame. The VLAN header consists of two subfields: the tag protocol identifier (TPID) and the tag control information (TCI). The TCI subfield contains three subfields: the priority code point (PCP), the drop eligible indicator (DEI), and the VLAN identifier (VID). The PCP subfield is a 3-bit field that specifies the priority level of the frame, ranging from 0 (lowest) to 7 (highest). The PCP values can be used to implement quality of service (QoS) mechanisms on bridges and switches12.
References: HTML rt Tag - W3Schools, VLAN 0 Priority Tagging Support - Cisco
NEW QUESTION # 45
Which statement accurately defines an Autonomous System (AS)?
- A. An AS is a collection of IS-IS routes imported into BGP and presented in such a way that networks connected to the AS have a global overview of the network.
- B. An AS is a group of networks directly connected to each other that can distribute eBGP information using directly established links.
- C. An AS is a network that is capable of autonomously forwarding packets, regardless of direct or indirect connectivity to the Internet.
- D. An AS is a set of routers under a single administration, using an interior gateway protocol and common metrics to route packets within the AS.
Answer: D
Explanation:
Explanation
The statement that accurately defines an Autonomous System (AS) is that an AS is a set of routers under a single administration, using an interior gateway protocol and common metrics to route packets within the AS.
An AS is a logical grouping of networks that share a common routing policy and operate under a single administrative authority. An AS can be a single network or a collection of networks that are interconnected by routers. An AS uses an interior gateway protocol (IGP), such as OSPF or IS-IS, to exchange routing information within the AS. An IGP uses common metrics, such as hop count or bandwidth, to determine the best path to each destination within the AS. An AS also has a unique number assigned by IANA, called an AS number (ASN), which identifies the AS in interdomain routing .
References: [Autonomous system (Internet) - Wikipedia], [What Is an Autonomous System? - Cisco]
NEW QUESTION # 46
Which two statements are true about router node hardening? (Choose two.)
- A. Any unnecessary services should be disabled within each context.
- B. IPsec should be implemented to secure IGP routing protocols.
- C. LDAP, using the TLS protocol, should be implemented for remote logging.
- D. Enabling syslog ensures system events are logged to a remote server.
Answer: A,D
Explanation:
Explanation
Two statements that are true about router node hardening are:
Any unnecessary services should be disabled within each context. Router node hardening is a process of securing a router from unauthorized access and attacks by applying various configurations and policies.
One of these configurations is to disable any services that are not needed for the router's functionality or purpose, such as telnet, ftp, http, etc. This reduces the attack surface of the router and prevents potential exploits of these services91.
Enabling syslog ensures system events are logged to a remote server. Syslog is a protocol that allows a router to send system messages and events to a remote server for logging and analysis. By enabling syslog on a router, network administrators can monitor the router's activity and performance, troubleshoot problems, detect anomalies, and audit security events101.
References: Cisco Router Hardening Step-by-Step | SANS Institute, Security Hardening Checklist Guide for Cisco Routers/Switches in 10 Steps, CCNA SEC: Router Hardening - Cisco Press
NEW QUESTION # 47
Which action will influence BGP route selection within your AS?
- A. changing the administrative distance for eBGP
- B. reducing number of hops in the network
- C. changing the default link metric
- D. changing the default value of the local preference
Answer: D
Explanation:
Explanation
The action that will influence BGP route selection within your AS is changing the default value of the local preference attribute. The local preference attribute is used to indicate the preference of a path among multiple paths learned from different external BGP neighbors or autonomous systems (ASes). The higher the local preference value, the more preferred the path is within your AS, and vice versa. The default value of local preference is 100, but you can change it using route maps or other configuration methods on your BGP routers. References: Ericsson IP Networking - Routing Protocols, BGP Attributes and Path Selection, BGP Local Preference Attribute: Controlling Traffic Like a Pro
NEW QUESTION # 48
Which statement is true about LDP?
- A. LDP performs routing functions along with IGP.
- B. LDP and IGP both exchange their databases every 30 seconds.
- C. LDP and IGP both exchange their databases every 60 seconds.
- D. LDP relies on IGP for all routing-related decisions.
Answer: D
Explanation:
Explanation
LDP relies on IGP for all routing-related decisions. LDP is a protocol that distributes labels in an MPLS environment, but it does not perform any routing functions. LDP uses the underlying routing information provided by an IGP, such as OSPF or IS-IS, to forward label packets. LDP and IGP do not exchange their databases at regular intervals, but rather use hello messages to maintain adjacencies and sessions. References: Ericsson IP Networking - Routing Protocols, Label Distribution Protocol - Wikipedia
NEW QUESTION # 49
Review the exhibit.
Referring to the exhibit, which two Ericsson routers support the 100GE interface? (Choose two.)
- A. Router 6672
- B. Router 6273
- C. Router 6675
- D. Router 6471
Answer: A,C
Explanation:
Explanation
Referring to the exhibit, the two Ericsson routers that support the 100GE interface are Router 6675 and Router
6672. The 100GE interface is a high-speed Ethernet interface that operates at 100 gigabits per second. The Ericsson Router 6000 series is a family ofrouters that provide IP transport for mobile and fixed networks. The Router 6675 is a 5G combined access and E-RAN switch with 100GE interfaces and 320Gb forwarding capacity. The Router 6672 is a high-capacity metro aggregation router with 100GE interfaces and 1.6Tb forwarding capacity12.
References: Router 6000 Series - Ericsson, New Ericsson Router 6000 series couples radio and IP transport for
5G future - Global Brands Magazine
NEW QUESTION # 50
Which two label actions are performed by a P router? (Choose two.)
- A. swap
- B. push
- C. php
- D. drop
Answer: A,C
Explanation:
Explanation
A P router is a provider router that is part of the service provider's core network in an MPLS environment. A P router does not have any customer routes or VPN information, but only has information about how to reach other P routers and PE routers in the same MPLS domain. A P router performs label switching, which means that it forwards labeled packets based on their top label in the label stack. A P router can perform two possible label actions:
Swap: The P router replaces the incoming label with a new label that corresponds to the next hop along the label-switched path (LSP). The new label is determined by looking up the label forwarding information base (LFIB) based on the incoming label and interface.
PHP: The P router removes the top label from the packet at the penultimate hop before reaching the egress PE router. This is done to avoid an extra lookup on the egress PE router, which can forward the packet based on its IP header or another label in the stack.
A P router does not perform push or drop actions on labels. A push action means adding one or more labels to the packet, which is done by an ingress PE router when initiating an LSP. A drop action means discarding a packet, which is done by any router when there is no matching entry in its LFIB or routing table. References: Provider (P) Router in IP MPLS Network - Cisco Community, MPLS Fundamentals: Forwarding Labeled Packets - Cisco Press, MPLS Label Switching | MPLS Operation | Push, Swap,Push IPCisco
NEW QUESTION # 51
Review the exhibit.
In the exhibit, which action is performed by router R4?
- A. swap
- B. push
- C. PHP
- D. pop
Answer: A
Explanation:
Explanation
In the exhibit, router R4 is performing a swap action. This means that router R4 is replacing the incoming label with a new label and forwarding the packet to the next hop along the LSP. In this case, router R4 receives a packet with label 20 from router R3 and swaps it with label 30 before sending it to router R5.
The exhibit shows an example of an MPLS network with four routers: R1, R2, R3, and R4. Router R1 is the ingress PE router and router R4 is the egress PE router. Router R2 and R3 are P routers. Router R1 assigns label 10 to the packet and sends it to router R2. Router R2 swaps label 10 with label 20 and sends it to router R3. Router R3 swaps label 20 with label 30 and sends it to router R4. Router R4 removes label 30 from the packet and forwards it based on its IP header or another label in the stack.
Therefore, the answer is D.
References: MPLS Label Switching | MPLS Operation | Push, Swap,Push IPCisco, A Complete Guide to Multiprotocol Label Switching (MPLS) - G2, Multiprotocol Label Switching - Wikipedia
NEW QUESTION # 52
Which two features does IPsec provide? (Choose two.)
- A. controlling the path through the network
- B. hiding the content of packets from observation
- C. protecting packets from modification
- D. protecting the length of packets from discovery
Answer: B,C
Explanation:
Explanation
IPsec provides two main features: protecting packets from modification and hiding the content of packets from observation. IPsec protects packets from modification by using cryptographic algorithms to generate and verify message authentication codes (MACs) or digital signatures for each packet. These mechanisms ensure that the packets have not been tampered with or altered in transit by unauthorized parties. IPsec hides the content of packets from observation by using encryption algorithms to scramble the payload of each packet. This prevents eavesdroppers or interceptors from reading or analyzing the data carried by the packets12.
References: What is IPsec? | How IPsec VPNs work | Cloudflare, IPsec - Wikipedia
NEW QUESTION # 53
An IS-IS router has been assigned the NSAP address: 49.00F0.0100.5012.3010.00.
What is the Area ID to which the router belongs?
- A. 5012.3010.00
- B. 49.00F0
- C. 49.00F0.0100
- D. 00F0 0100
Answer: C
Explanation:
Explanation
The Area ID to which the router belongs is 49.00F0.0100. The Area ID is a variable-length field in the NSAP address that identifies the area to which the router belongs. The Area ID can be between 1 and 13 bytes long, but it must start and end with an octet (8 bits). The NSAP address is composed of three parts: the authority and format identifier (AFI), the area ID, and the system ID. The AFI is a one-octet field that indicates the format and authority of the rest of the address. The system ID is a fixed-length field of six octets that uniquely identifies the router within an area. The NSAP address also has a network selector (NSEL) field, which is a one-octet field that identifies the network layer service to which a packet should be sent. For IS-IS routers, the NSEL must always be 00.
In this question, the NSAP address is 49.00F0.0100.5012.3010.00. This means that:
The AFI is 49, which indicates a private address.
The Area ID is 00F0.0100, which is four octets long and starts and ends with an octet.
The system ID is 5012.3010, which is six octets long and identifies the router within the area.
The NSEL is 00, which indicates IS-IS.
Therefore, the answer is B.
References: Ericsson IP Networking - Routing Protocols, IS-IS NSAP address - Cisco Community, Understanding IS-IS NSAP Addresses - Todd Lammle, LLC, IS-IS - Nokia, Network service access point address - Wikipedia
NEW QUESTION # 54
......
ECP-206 Actual Questions Answers PDF 100% Cover Real Exam Questions: https://www.actualtests4sure.com/ECP-206-test-questions.html
ECP-206 Exam questions and answers: https://drive.google.com/open?id=1su5JiUtOdMcmN_YuDChfcPblc4YJzQX5
