Achive your Success with Latest NACE NACE-CIP1-001 Exam [Apr 08, 2023]
The NACE-CIP1-001 Exam Test For Brief Preparation
NEW QUESTION # 60
Common errors that can produce inaccurate readings when using Wet Film Thickness (WFT) gauges include:
Select All That Apply
- A. Using a damaged gauge
- B. Dragging a gauge through wet coating
- C. Placing the gauge along the longitudinal axis
Answer: A,B
NEW QUESTION # 61
An inspectors personal log book should contain:
- A. No comments regarding the application team
- B. Objective comments regarding the application work
- C. The inspector's personal opinions of the application team
- D. Subjective comments re ding the application team
Answer: A
NEW QUESTION # 62
When performing tests for oil and grease using an ultra-violet light, the NACE Inspector should be aware that:
- A. Chloride salt may produce a false positive
- B. Ultra-Violet light may contaminant the surface
- C. Presence of weld spatter may produce a false positive
- D. Synthetic oil or grease may not be identified
Answer: D
NEW QUESTION # 63
The least effective method of surface cleaning is most likely
- A. water blasting.
- B. hand tool cleaning.
- C. power tool cleaning.
- D. dry grit blasting.
Answer: B
NEW QUESTION # 64
Which of these tests uses a syringe?
- A. Bresle patch
- B. Sleeve test
- C. Soluble salts meter
- D. Potassium ferricyanide
Answer: A
NEW QUESTION # 65
Which is a component that supplies most of the features and functions of the material?
- A. additive
- B. binder
- C. pigment
- D. solvent
Answer: B
NEW QUESTION # 66
Safety Data Sheets must be carefully reviewed by:
- A. The Inspection personnel
- B. The Owner's personnel
- C. The Application personnel
- D. All personnel involved in the job
Answer: D
NEW QUESTION # 67
Due to a previous premature coating failure the owner has required the original coating applicator to return to remove and replace 10,000 square feet of a failed three coat system at the applicator's cost. Due to the financial implications of another failure, the owner has offered you the job as the NACE CIP Level 1 Coating Inspector and explained that he expects you to be his "insurance policy" for this job. You have never been involved in a warranty job before and are unfamiliar with the coating system.
Your preferred FIRST course of action is to:
- A. Meet with the owner and explain your limitations and concerns prior accepting the assignment
- B. Purchase Professional Liability Insurance prior to job commencement
- C. Review the Product Data Sheets and meet with the Coating Applicator 'prior to the pre-job meeting
- D. Review the Product Data Sheets, and conduct a walk thru of the job site prior to the pre-job Conference
Answer: D
NEW QUESTION # 68
Which one of the following documents is the best source for coating technical data:
- A. Technical Data Sheet
- B. Safety Data Sheet;
- C. Specification
- D. Application Guidelines
Answer: A
NEW QUESTION # 69
Upon arrival of coating materials, the inspector should
- A. observe and document time frame and environmental conditions between each coat.
- B. observe and document the amount of material and batch numbers.
- C. review coating contractors' plans for storage of coating materials and confirm they meet national, local and owners' fire and environmental regulations.
- D. observe aryl document that the applicator WFT at regular intervals during application.
Answer: B
NEW QUESTION # 70
You are the NACE Inspector on a tank lining project where a 50% solids epoxy tank lining is being applied. After application of the 19 coat you notice small blisters in some areas of the applied lining.
Your FIRST preferred course of action is to:
- A. Document the problem and advise the Contractor and Owner's representative
- B. Break the blisters to see what's inside
- C. Document the problem and advise the Contractor
- D. Extract any liquid that may be inside the blister and send it to the lab for further analysis
Answer: A
NEW QUESTION # 71
You are an inspector on a project where SSPC SP 3 is specified.
What sort of tools should you expect the Contractor to use to achieve the standard?
- A. Abrasive blast nozzles
- B. Power tools
- C. Airless spray equipment
- D. Hand tools
Answer: B
NEW QUESTION # 72
ISO SA 3 is directly equivalent to:
- A. None of the above
- B. NACE No. 3/SSPC SP 6
- C. NACE No. 2/SSPC SP 10
- D. NACE No. 1/SSPC SP 5
Answer: A
NEW QUESTION # 73
NACE SP 0178 is a standard for:
- A. Stainless steel pipe to be Externally Coated
- B. Structural steel to be coated for Atmospheric Service
- C. Tanks and Vessels to, be Lined for Immersion Service
- D. Tanks and Vessels to be Externally Coated
Answer: C
NEW QUESTION # 74
ASTM Standards are applicable:
- A. In North America
- B. When specified
- C. In Asia
- D. In the USA
Answer: B
NEW QUESTION # 75
According to SSPC PA 2 a Spot Measurement is:
- A. A single gauge reading
- B. The average of all spot measurements in a given area
- C. The overall average of all readings
- D. The average of gauge readings taken in a 4cm (1.5 inch) circle
Answer: D
NEW QUESTION # 76
......
Revolutionary Guide To Exam NACE Dumps: https://www.actualtests4sure.com/NACE-CIP1-001-test-questions.html
Pass NACE-CIP1-001 Exam Latest Practice Questions: https://drive.google.com/open?id=1P5ahCm6k7BWu6QZEO30gyhR5TmoCNhw7
