Updated Dec 26, 2023 300-610 Exam Dumps - PDF Questions and Testing Engine
New (2023) Cisco 300-610 Exam Dumps
Cisco 300-610 exam is intended for experienced professionals who are responsible for designing and implementing data center infrastructure. 300-610 exam covers a wide range of topics, including data center infrastructure design, network design, storage design, compute design, automation design, and security design. Candidates are required to have a deep understanding of Cisco data center technologies, including Cisco Nexus switches, Cisco UCS servers, Cisco ACI, and Cisco HyperFlex. Candidates are also expected to have hands-on experience in designing and implementing data center infrastructure solutions.
NEW QUESTION # 79
Refer to the exhibit.
A high-availability setup for iSCSI is designed with the host running ISCSI software. Each storage port on the MDS exports the same two Fibre Channel target ports with different ISCSI target names. In this design, how many ISCSI session are created from the host so that recovery occurs if any component fails?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: A
Explanation:
Reference:
NEW QUESTION # 80
Drag and drop the technologies from the left onto the correct descriptions on the right.
Answer:
Explanation:
NEW QUESTION # 81
An engineer must design a Cisco UCS environment for a customer The design requires the most efficient use of available bandwidth with active-active uplinks The upstream Cisco Nexus 9000 Series Switch must automatically initiate the port-channel connectivity to the fabric interconnects Which configuration must the engineer choose to meet these requirements?
- A. * fabric interconnects in Ethernet switching mode
* LACP port-channel from fabric interconnects and Cisco Nexus 9000 switches - B. * fabric interconnects in Ethernet switching mode
* static port-channel from fabric interconnects and Cisco Nexus 9000 switches - C. * fabric interconnects in Ethernet end-host mode
* static port-channel from fabric interconnects and Cisco Nexus 9000 switches - D. * fabric interconnects in Ethernet end-host mode
* LACP port-channel from fabric interconnects and Cisco Nexus 9000 switches
Answer: D
Explanation:
Reference:
Cisco UCS Fabric Interconnect in Switch Mode with Cisco MDS 9000 Family Fibre Channel Switching Modules When the Cisco UCS Fabric Interconnect is in switch mode, the port channel mode can only be in ON mode and not Active . However, to get the peer wwn information for the Fabric Interconnect, the port channel must be in Active mode.
NEW QUESTION # 82
Which feature must be configured to connect a classical Ethernet network to a data center network so that the data center network appears to be one large switch.
- A. EVPN
- B. OSPF
- C. VPC+
- D. UDLD
Answer: C
Explanation:
A vPC allows links that are physically connected to two different Nexus switches to appear as single portchannel to a server or another switch.
NEW QUESTION # 83
What can be implemented on Cisco Nexus 5600 Series Switches for link redundancy within a Fibre Channel fabric?
- A. SAN port channel
- B. vPC+
- C. LACP port channel
- D. E-Trunk
Answer: A
NEW QUESTION # 84
Which two naming formats identify target or initiator iSCSI nodes? (Choose two.)
- A. IQN
- B. EUI
- C. WWPN
- D. WWN
- E. OUI
Answer: A,D
Explanation:
https://docs.vmware.com/en/VMware-vSphere/5.5/com.vmware.vsphere.storage.doc/GUID-686D92B6-A2B2-4944-8718-F1B74F6A2C53.html
NEW QUESTION # 85
An engineer is implementing a Cisco UCS environment The requirements for the solution are for the MAC addresses to be learned only on the server-facing ports. The use of the Spanning Tree Protocol must be avoided. Also, the engineer must have deterministic traffic handling from blades to uplink ports.
Which two settings must be selected to meet these requirements? (Choose two.)
- A. end-host mode
- B. dynamic pinning
- C. static pinning
- D. NPIV mode
- E. switching mode
Answer: A,C
NEW QUESTION # 86
A network engineer must perform a VMM integration for the VMWare vCenter platform with the Cisco ACI Fabric. The vCenter is already installed in one of the rack servers connected to ACI leaf switches in a vPC mode. Which type of management network must be used to integrate vCenter with ACI?
- A. out-of-band management
- B. In-band management
- C. ARC infra
- D. VLAN infra
Answer: A
NEW QUESTION # 87
An engineer must configure an interface for managing and orchestrating a Cisco Nexus device. The interface must be operational if the data and control planes crash, support IPv4 and IPv6 addressing, and have access to its own VRF instance.
Which interface should be used to meet these requirements?
- A. loopback interface
- B. management interface
- C. physical interface
- D. interface VLAN
Answer: B
NEW QUESTION # 88
A customer attaches an additional storage appliance to an existing Cisco UCS domain, which contains 50 virtualization hosts that require fabric failover connectivity on fabric interconnect B. The interfaces are bound to a separate pin group to segregate traffic with a CoS value of 0 Which Cisco UCS Manager feature meets these requirements?
- A. SAN connectivity policy
- B. vNIC Template
- C. vHBA Templates
- D. storage policy
Answer: C
NEW QUESTION # 89
An engineer must design a multitenant solution using Cisco 7709 switches. The solution must support separate routing instances, separate spanning tree domains, and separate firewalls for each tenant. Which solution meets these requirements?
- A. CFS
- B. VRF
- C. vPC
- D. VDC
Answer: D
NEW QUESTION # 90
An engineer must design a Cisco HyperFlex solution to support a virtualized environment in a single data center location. The design must consider these customer requirements:
a large-scale cluster with eight or more nodes
distributed high-performance file system for virtualized servers
high fault tolerance to multiple node failures
Which action meets these objectives?
- A. Create multiple datastores for storage of VM.
- B. Configure data destaging and deduplication
- C. Enable logical availability zones.
- D. Implement a replication factor of four.
Answer: B
NEW QUESTION # 91
Refer to the exhibit.
A high-availability setup for iSCSI is designed with the host running iSCSI multipath software. Each IP storage port on the MDS switch exports the same two Fibre Channel target ports with different iSCSI target names.
In this design, how many iSCSI sessions are created from the host so that recovery occurs if any component fails?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: A
NEW QUESTION # 92
Drag and drop the components from the left onto the descriptions on the right that indicate what occurs to Fibre Channel fabric when that component fails.
Answer:
Explanation:
NEW QUESTION # 93
A customer requires a tool to manage Cisco network hardware. The solution must use secure communication using a secure network protocol, support the use of declarative language to manage the state of resources, and periodically pull changes to the controlled nodes. Which tool meets these requirements?
- A. Puppet
- B. Nomir
- C. SaltStack
- D. Ansible
Answer: A
NEW QUESTION # 94
......
Updated Verified Pass 300-610 Exam - Real Questions and Answers: https://www.actualtests4sure.com/300-610-test-questions.html
Best Way To Study For Cisco 300-610 Exam Brilliant 300-610 Exam Questions PDF: https://drive.google.com/open?id=1Z06YC0HVdvnzToKYGl6KHo6nX05SWXQS
